The Blind Alley, Custom Drapery and Window Covering Specialists serving Bellevue, Washington and the Greater Seattle area since 1984.


LEVOLOR MARK I CORDLESS BLINDS
INSTALLATION INSTRUCTIONS

Levolor Mark I Cordless Blinds Info

Thank you for purchasing your new Levolor Mark I Cordless Blind. You can take pride in the fact that you have made a quality purchase that will add beauty and function to your home.

Your new Mark I Cordless blind mounts with concealed brackets, giving a clean appearance and eliminating the need for a valance.

   Levolor Smart Control Cordless Blind and Shade Operating System


Diagram A

Levolor Mark I Cordless Blind Parts


Diagram B

Fasteners for Levolor Mark I Cordless Blinds


Check For All Hardware

Be sure you have all the components identified in Diagram A, above including the following for each blind:

Assembled Mark I Cordless Blind

Tilt Wand

2 (or more) Brackets

Bracket Template

4 (or more) Installation Screws

2 Hold Down Brackets

2 Hold Down Pins

6 Plastic Spacers for Bracket Alignment


Tools You Will Need

Phillips screwdriver or 1/4" hex driver

Hand or electric drill with 7/64" drill bit

Pencil

Tape measure

When using tools, make sure you wear proper eye protection.


Choose the Proper Fasteners

For installation in wood or aluminum frames, Levolor recommends you use the sheet metal screws included with your Mark I Cordless blind. For other types of wall or window construction, you will need to furnish different fasteners.


Fastener Options

See Diagram B above for the following different types of fasteners:

# 8 Screws for wood or aluminum

Plastic insert plugs for drywall or plaster

Auger threaded metal or plastic inserts for drywall

Molly bolts for drywall

Toggle bolts for drywall or lath & plaster

Note: Fastener strength should be rated more than the weight of the blind.


Attach the Brackets

The brackets supplied are appropriate to your order, either inside or outside mount.

Diagram E

Levolor Mark I Cordless Blinds End Bracket Spacing

Determine where to attach each bracket. Use the bracket template to simplify installing the Levolor Mark I Cordless Blind. It positions the bracket 2-1/8" from the end of the headrail and aligns the mounting holes in the correct location (Diagram E). For the inside mount bracket, fold the template along the scored line and use two of the four front holes. The template provides all hole locations for the bracket. Note that one of the brackets is positioned over the cordlock to prevent the headrail from shifting.

Bracket Template

Levolor Mark I Cordless Bracket Template

Diagram C

Levolor Mark I Cordless Blind Inside Mount Bracket

Inside Mount Installation

To attach the inside mount brackets so the headrail aligns flush with the window pocket, attach the bracket so the tongue is approximately 1/16" from the window frame edge (Diagram F). Depending on the width of the blind, you may receive additional brackets. Be sure to space additional brackets evenly across the length of the headrail. Be sure to use all brackets supplied.

Diagram D

Levolor Mark I Cordless Blind Outside Mount or Universal Bracket

Outside Mount Installation

The Levolor Mark I Cordless Blind uses the outside mounting bracket (Diagram D) for outside mount installations. This bracket is 2" wide by 1" high. When possible, mounting screws should attach to a wall stud; otherwise, use plastic anchors or toggle bolts to secure the bracket to the wall. Insert screws through two holes in the back of the bracket. Depending on the width of the blind, you may receive additional outside mount brackets. Be sure to space additional brackets evenly across the length of the head rail. Be sure to use all brackets supplied.

On some Levolor Mark I Cordless blinds it will be necessary to inspect the inside of the headrail and determine a proper spacing that will not interfere with the internal hardware in the headrail.

Mark the bracket hole locations.

Drill pilot holes using the 7/64" diameter drill bit.

Use at least 2 screws per bracket.

Insert screws through the holes in the top of the brackets for inside mounted blinds.

Insert screws through the holes in the back of the brackets for outside mounted blinds.

Brackets must be aligned with each other.

Use the plastic spacers to align brackets on inside mounts.

Diagram C shows the Inside Brackets for Levolor Mark I Cordless Blinds.

Diagram D shows the Outside Brackets for Levolor Mark I Cordless Blinds.

Diagram F

Levolor Mark I Cordless Blind Inside Mount Setback


Installing Spacers with Standard Brackets

The Levolor Mark I Cordless Blind is designed to fit closely to the mounting surface. However, soft wallboard or uneven surfaces affect the blind's ability to engage the bracket (Diagram G). Spacers are provided to eliminate this problem. For each inside mount bracket, first loosen the bracket screws just enough to slide a spacer in between the mounting area and the bracket. Then slide a spacer in until the spacer is flush with the front of the bracket mounting surface (Diagram H). Tighten down the bracket and check the distance between the bracket tongue and the mounting surface. Install additional spacers if necessary.

Diagrams G & H

Levolor Mark I Cordless Blind Spacers

Levolor Mark I Blinds with spacers


Install the Headrail

The following procedure applies to inside mount Levolor Mark I Cordless blinds.

Place the front lip of the headrail over the barb on the bracket tongue, and then push the headrail back so that the tongue slides back into the bracket (Diagram I).

Diagram I

Levolor Mark I Cordless Blind Headrail Installation Step 1

Rotate the back of the headrail up until the lip clears the hook at the rear of the bracket (Diagram J).

Diagram J

Levolor Mark I Cordless Blind Headrail Installation Step 2

Guide the headrail forward and then down until both lips are resting over both the front and rear bracket hooks (Diagram K).

Diagram K

Levolor Mark I Cordless Blind Headrail Installation Step 3

Be sure the Levolor Mark I Cordless blind is properly secured in the brackets before operating the blind.

To remove the Levolor Mark I Cordless blind, simply reverse the action.


The following procedure applies to outside mount Levolor Mark I blinds and all Mark I blinds using the Universal bracket.

With the blind facing you, tilt the bottom of the blind toward you and place the front lip of the headrail over the barb on the bracket tongue (Diagram KK).

Rotate the headrail up until the rear lip clears the hook at the rear of the bracket.

Levolor Mark I Cordless Headrail Installation Step 4

To remove the Levolor Mark I Cordless blind, locate the bracket tongues holding the lower part of the blind. Pry the tongue back (this may require the use of a screwdriver). While providing support for the blind, allow the blind to rotate away from the bracket.


Attach the Tilt Wand

You may need to attach the wand to the tilt gear stem. Push the tilt wand up onto the metal Tilter Loop as shown in Diagram L. Rotate the tilt wand to open and close the blind slats.

Diagram L

Install Levolor Mark I Cordless Blind Tilt Wand


To Raise and Lower the Mark I Cordless Blind

To raise your Levolor Mark I Cordless blind simply place your hand under the bottom rail at the mid-point of the bottom rail. Then apply gentle upward pressure to the bottom rail. The Mark I Cordless blind will stay in place wherever you stop lifting.

   How to Raise and Lower Mark I Cordless Blinds

To lower the Levolor Mark I Cordless blind, pull down the bottom rail while holding it at the mid-point.

You will find that the Levolor Mark I Cordless blind will raise and lower more smoothly if you first open the slats so that they are level and you can see through them before raising or lowering the blind.


Remove the Protective Paper

There is a protective paper covering on the face of your new Levolor Mark I Cordless blind headrail. Remove it carefully when all other installation steps have been successfully completed.


Hold Down Brackets

These brackets are used only where it is desirable to keep the bottom of the blind from swinging freely, such as on a door.

To Install the Hold Down Brackets:

Install the white nylon pins into the bottom rail on each end.

Install the blind and lower it all the way down.

Mark the position of the Hold Down brackets.

Screw the Hold Down brackets to the surface as shown in Diagram N.

Slip the pin into the Hold Down bracket as shown.

Diagram N

Install Levolor Mark I Cordless Blind Hold Down Brackets


If you need any assistance installing the products listed above or if you have any questions about the products, contact us here.

If you need any assistance installing the products listed above or if you have any questions about the products, contact us here.


To learn more about The Blind Alley visit our Company Profile.

  About The Blind Alley


Search Blind Alley's Website

Click here to search our Website or visit our website Navigation page or website Directory.

Click here to visit our website Navigation Tips page         Click here to view our contact information.         Click here to visit our website Directory